UV resistant filament: what the datasheets say
Among the Bambu Lab grades we print or order in, three datasheets state UV resistance for outdoor use, all ASA. ASA Aero is one of our most popular materials; ASA and ASA-CF are ordered in. Ten more grades carry a UV tick on their product page and nothing in their datasheet, so we do not rate them for permanent sun.
- 3 datasheets state UV resistance: ASA, ASA-CF, ASA Aero
- 10 more grades: a product-page tick, a silent datasheet
- ASA Aero 2-5 working days after payment; ASA and ASA-CF ordered in
- Up to 340 x 320 x 340 mm in the ASA family
Which filament is UV resistant?

For a part that lives in the sun, choose ASA. ASA Aero for light covers and housings: its datasheet states "extraordinary resistance to temperature, water, and UV rays", and it is one of our most popular materials. ASA for a part that carries load, ASA-CF for one that must stay stiff; both are ordered in.
PETG HF, PC FR and the carbon fibre materials have a UV tick on Bambu Lab's product page but no UV statement in their datasheet, so we do not rate them for permanent sun.
How we checked
We read the datasheets of the 22 Bambu Lab grades in our catalogue and searched each one for "UV", "weather", "outdoor", "sunlight", "xenon" and the two common weathering standards, ISO 4892 and ASTM G154. UV appears in four datasheets: ASA, ASA-CF, ASA Aero and ABS. Not one names an exposure test, an hour count or a retained-property figure.
Then we put each datasheet next to Bambu Lab's product page for the same grade, where a list of pros and cons includes a "UV resistant" tick for some grades. The two sources disagree on ten grades. The table below shows both, grade by grade, and what we do with each.
A silent datasheet is not a failing grade; it is no grade at all.
We read datasheets. We ran no exposure test of our own, and no figure on this page is ours.
Datasheet against product page
Datasheet wording is quoted from the Basic Info of each TDS. Product-page wording is the tick or the con in Bambu Lab's pros and cons list, captured in summer 2026; Bambu Lab may have changed a tick since.
| Datasheet on UV | Bambu Lab product page | Our status | |
|---|---|---|---|
| ASA Aero | Datasheet on UV"extraordinary resistance to temperature, water, and UV rays" (TDS V1.0) | Bambu Lab product page"Water & UV resistance" | Our statusmost popular |
| ASA | Datasheet on UV"exceptional UV, weather, mechanical, and thermal resistance" (TDS V3.0) | Bambu Lab product page"UV resistant" | Our statusordered in |
| ASA-CF | Datasheet on UV"exceptional weather and UV resistance" (TDS V1.0) | Bambu Lab product page"UV Resistant" | Our statusordered in |
| PETG HF | Datasheet on UVnot stated | Bambu Lab product page"Water & UV Resistant" | Our statusmost popular; white PETG HF is 24/7 PETG |
| PET-CF, PPA-CF, PPS-CF, PC FR | Datasheet on UVnot stated | Bambu Lab product pageticked "UV resistant" | Our statusmost popular |
| PETG-CF, PC, PA6-CF, PA6-GF, PAHT-CF | Datasheet on UVnot stated | Bambu Lab product pageticked "UV resistant" | Our statusordered in |
| PLA Basic | Datasheet on UVnot stated | Bambu Lab product page"Low UV resistance", listed as a con | Our statusmost popular |
| TPU for AMS | Datasheet on UVnot stated | Bambu Lab product pagenothing either way | Our statusmost popular |
| TPU 95A HF, TPU 90A, TPU 85A, PLA-CF, PLA Pure | Datasheet on UVnot stated | Bambu Lab product pagenothing either way | Our statusordered in |
The count: 3 datasheets state UV resistance for outdoor use, 1 mentions it in a clause (ABS, below), 18 are silent: the 17 grades in the table and ABS-GF. The product pages tick UV for 13 grades: the three ASA grades and ten whose datasheets say nothing. ASA Aero has a store listing rather than a product page; its UV wording is in its datasheet too, so it sits in the stated group.
Bambu Lab also lists "Outdoor Use" as an application for PETG HF, PC, PC FR, PET-CF, PA6-CF, PA6-GF, PAHT-CF, PLA-CF and ABS. An application list is not a rating, and we do not read it as one.
If it lives in the sun: which ASA
- ASA AeroThe light one, a foaming ASA: 0.99 g/cm³ (ISO 1183). Tensile strength 32 MPa along the layers and 21 MPa across them (ISO 527); impact across the layers 3.4 kJ/m² (ISO 179). Covers, housings and light outdoor parts. One of our most popular materials; more on ASA Aero.
- ASAThe one that carries load. Heat deflection 92 °C at 1.8 MPa (ISO 75), tensile strength 37 MPa along the layers and 31 MPa across them (ISO 527). Brackets, mounts and fixings in the sun. Ordered in; the quote gives the time.
- ASA-CFThe stiff one. Heat deflection 102 °C at 1.8 MPa (ISO 75) and a bending modulus of 3,740 MPa along the layers (ISO 178), the highest of the three. It gives up toughness for that: 14.0 kJ/m² impact along the layers against ASA's 41.0 (ISO 179). Stiff outdoor parts that must hold their size. Ordered in; the quote gives the time.
All three datasheets read "Resistant" to acid and alkali and "Not resistant to some organic solvents". A part that sits in sun and in fuel or solvent has no single answer in the catalogue: PPS-CF resists the solvent and its datasheet is silent on UV. Say which matters more and a person picks.
All three print in a heated chamber, so the largest ASA part in one piece is 340 x 320 x 340 mm.
A tick without a datasheet
PETG HF's product page ticks "Water & UV Resistant". Its datasheet has no UV row and no UV sentence. The same holds for PC FR and for the carbon fibre grades on our most popular list, PET-CF, PPA-CF and PPS-CF. We take the datasheet as the record, so none of these is rated for permanent sun here.
Why the silence matters: polycarbonate as a resin is, in the words of one plastics failure-analysis firm, "highly susceptible to yellowing through ultraviolet radiation (UV) exposure", and UV stabilisers can improve that. Bambu Lab's PC and PC FR datasheets say nothing about stabilisers either way. That is not a statement that PC FR yellows; it is the reason we do not promise that it will not.
Out of direct sun these materials are still the right choice. PETG HF is the material we print most, and white PETG HF is 24/7 PETG. PC FR is the flame-retardant housing, PPS-CF the part in heat and chemicals, PPA-CF the stiff bracket. Sun is the one axis their datasheets do not cover. For the PETG-or-ASA decision on one outdoor part, heat in the sun included, see PETG or ASA for outdoor parts.
PLA and TPU
PLA Basic is the one grade whose product page says the opposite: "Low UV resistance", listed as a con. Its datasheet is silent. We print PLA Basic from our usual range for indoor parts and do not suggest it for anything in the sun. PLA-CF's product page lists "Outdoor Use" as an application and "Low heat resistance" as a con, with no UV statement anywhere.
TPU for AMS, TPU 95A HF, TPU 90A and TPU 85A have nothing: no tick, no con, no datasheet sentence. The question "is TPU for AMS UV resistant?" has no answer from Bambu Lab, and we do not supply one. A flexible part in the sun is a part you test.
ABS: two Bambu Lab pages disagree
The ABS datasheet's Basic Info calls ABS "known for its superior comprehensive properties such as high temperature resistance, UV resistance and water resistance". The ABS product page lists no UV pro. Bambu Lab's ASA page calls ASA "a common alternative to ABS, offering improved UV, temperature, and impact resistance".
Three statements, two directions. We rate nothing from them. ABS-GF says nothing on UV either way. ABS is printed on request, ordered in.
What no datasheet tells you
How many hours of exposure the material was tested for. Whether the test was sunlight, a xenon lamp or a fluorescent UV lamp. How much colour it lost. How much strength or elongation it kept. Not one of the 22 datasheets gives any of these, for any grade, the ASA family included.
So "UV resistant" on this page means only what it says on the datasheet: a stated property, with no figure behind it. If your part must pass a weathering specification or keep its colour for a stated number of years, that is a test you run on the printed part. We print the test pieces; we certify nothing.
Tell us where it lives
Our quote form asks about heat, force, priority and chemicals. It has no sun question, because no datasheet gives a figure to score it on. Write it in the message instead: "outdoors, full sun", "under a carport", "inside a box on the roof". A person reads it before the price and picks between ASA Aero, ASA and ASA-CF, or says that shade makes PETG HF the better part.
- ASA Aero: one of our most popular materials, usually 2-5 working days after payment.
- ASA and ASA-CF: ordered in for the job; the quote gives the time. Ask for two materials in one request and the quote prices each.
- Largest ASA part in one piece: 340 x 320 x 340 mm. Tolerance ±0.5%, minimum ±0.5 mm.
- Posted to the Baltics, Finland, Sweden and Denmark. Reply in 3 hours on average on workdays.
Questions
Checked by the druckworks workshopUpdated
Is PETG UV resistant?
Bambu Lab's PETG HF product page ticks it; the datasheet does not state it. We do not rate PETG HF for permanent sun. Out of direct sun it is the material we print most.
Is PC FR UV resistant?
Its datasheet does not state UV resistance; its product page ticks it. We print PC FR for flame-retardant housings and do not rate it for permanent sun.
Is carbon fibre filament UV resistant?
Only ASA-CF's datasheet says so: "exceptional weather and UV resistance". It is ordered in. PPA-CF, PPS-CF, PET-CF, PETG-CF, PA6-CF and PAHT-CF carry a product-page tick and a silent datasheet; PLA-CF has neither a tick nor a datasheet sentence.
Is TPU UV resistant?
Bambu Lab says nothing either way for TPU for AMS, TPU 95A HF, TPU 90A or TPU 85A: no tick, no con, no datasheet sentence. We do not fill that gap.
What is the most UV resistant filament?
Among the Bambu Lab datasheets we print from, only the three ASA grades state UV resistance for outdoor use, and none gives a figure to rank them by. Pick between them on the other rows: ASA Aero for weight, ASA for load, ASA-CF for stiffness.
Which UV resistant material do you print fastest?
ASA Aero, one of our most popular materials: usually 2-5 working days after payment. ASA and ASA-CF are ordered in, so the quote gives the time.
How big can an ASA part be?
Up to 340 x 320 x 340 mm in one piece, for ASA Aero, ASA and ASA-CF alike.
Send the file and say where the part lives
Send the file and write "outdoors, full sun" or "under a roof" in the message. A person picks the material and replies with a price in 3 hours on average on workdays.
