Carbon fibre nylon 3D printing: PPA-CF, PA6-CF or PAHT-CF
Three carbon fibre nylons, three different base polymers. PPA-CF is the stiffest and strongest of the three and the one we print most. PAHT-CF takes knocks and, by Bambu Lab's account, keeps its properties wet; PA6-CF keeps the most impact strength across the layers. Those two are ordered in for the job. Every figure below is from Bambu Lab's datasheets.
- PPA-CF: 9,860 MPa bending modulus along the layers (ISO 178)
- PAHT-CF: 0.88% saturated water absorption, the lowest of the three
- PPA-CF 2-5 working days after payment; the other two ordered in
- Up to 340 x 320 x 340 mm in one piece
Which carbon fibre nylon should I choose?

Start with PPA-CF: 168 MPa tensile strength and a 9,860 MPa bending modulus along the layers, and 196 °C heat deflection at 1.8 MPa, the stiffest, strongest and most heat-tolerant of the three. It is also the one we print most, so it is usually the quickest.
Choose PAHT-CF when the part takes knocks, flexes a little or lives wet. Choose PA6-CF only for a dry part that is loaded across its layers. Both are ordered in; the quote gives the time.
The three side by side
Figures from Bambu Lab's datasheets for PPA-CF (TDS V1.0), PA6-CF (TDS V3.0) and PAHT-CF (TDS V3.0), measured on test specimens and given "for design reference and comparison only". X-Y is along the layers, Z across them.
| PPA-CF | PA6-CF | PAHT-CF | |
|---|---|---|---|
| Our status | PPA-CFmost popular | PA6-CFordered in | PAHT-CFordered in |
| Composition (datasheet) | PPA-CFSemi-aromatic nylon, carbon fibre | PA6-CFNylon 6, carbon fibre | PAHT-CFPA 12 and other long-chain PA, carbon fibre |
| Tensile strength, X-Y / Z (ISO 527) | PPA-CF168 / 57 MPa | PA6-CF102 / 48 MPa | PAHT-CF92 / 47 MPa |
| Bending modulus, X-Y / Z (ISO 178) | PPA-CF9,860 / 3,240 MPa | PA6-CF5,460 / 2,240 MPa | PAHT-CF4,230 / 1,820 MPa |
| Impact strength X-Y, unnotched / notched (ISO 179) | PPA-CF41.7 / 6.5 kJ/m² | PA6-CF40.3 / 13.4 kJ/m² | PAHT-CF57.5 / 22.8 kJ/m² |
| Impact strength Z (ISO 179) | PPA-CF4.3 kJ/m² | PA6-CF15.5 kJ/m² | PAHT-CF13.3 kJ/m² |
| Elongation at break, X-Y / Z (ISO 527) | PPA-CF3.2 / 0.9% | PA6-CF5.8 / 3.7% | PAHT-CF8.4 / 4.1% |
| Heat deflection at 1.8 MPa (ISO 75) | PPA-CF196 °C | PA6-CF164 °C | PAHT-CF170 °C |
| Saturated water absorption (25 °C, 55% RH) | PPA-CF1.30% | PA6-CF2.35% | PAHT-CF0.88% |
| Acids and alkalis | PPA-CFResistant to weak, not to strong | PA6-CFNot resistant | PAHT-CFNot resistant |
| Organic solvents | PPA-CFResistant to most | PA6-CFNot resistant to some | PAHT-CFNot resistant to some |
| Specimens before testing | PPA-CFAs printed, not annealed | PA6-CFAnnealed and dried, 80 °C for 12 h | PAHT-CFAnnealed and dried, 80 °C for 12 h |
The last row matters. PPA-CF was tested as printed; the other two were annealed and dried first, so the gap on paper is not a like-for-like test. Bambu Lab adds that PPA-CF printed in a hotter chamber (70-80 °C) would give higher figures, especially across the layers. All three resist most oils and greases, so that row is left out.
Read heat deflection as a loaded specimen test, not as the temperature a part can work at. The glass transition temperatures are far lower (85 °C for PPA-CF, 68 °C for PA6-CF, 70 °C for PAHT-CF, by DSC); a fibre-filled nylon holds its shape well above that under light load, which is what the heat deflection row measures.
Which one for which part
- PPA-CFThe default. Brackets, jigs, gear housings and mounts that must stay stiff and hold their size when warm: 9,860 MPa bending modulus and 196 °C heat deflection at 1.8 MPa. Its weak side is toughness: 4.3 kJ/m² impact across the layers and 3.2% elongation along them, so a clip that flexes or a part that gets dropped is not its job. For a part that also touches fuel or solvents, PPA-CF is the nylon we suggest and PPS-CF the material; see PPA-CF or PPS-CF.
- PAHT-CFThe tough one. 57.5 kJ/m² unnotched and 22.8 kJ/m² notched impact along the layers, 8.4% elongation and the lowest water uptake of the three at 0.88%. Bambu Lab says it was "optimized to retain excellent mechanical properties when wet" and has "enhanced Z-bonding". Pick it for a part that is knocked, flexed or kept damp. Ordered in for the job; the quote gives the time.
- PA6-CFThe dry-room one. Its 15.5 kJ/m² impact across the layers is the highest of the three, and its 102 MPa tensile strength sits between the other two. It takes up 2.35% water, and Bambu Lab places it in "structural parts used in dry environments". Pick it for an indoor part loaded across its layers; for anything damp, PAHT-CF. Ordered in for the job.
No datasheet gives a wet-strength figure for any of the three, so we quote none. For how the nylons rank against the rest of our range on water uptake, see Filament for wet and humid parts.
What the names mean
PPA is a semi-aromatic nylon, so PPA-CF is a carbon fibre nylon; Bambu Lab's datasheet lists its composition as "Semi-aromatic Nylon, carbon fiber". PA6-CF is nylon 6 with carbon fibre: "Nylon 6, carbon fiber" on the datasheet.
PAHT-CF is a trade name, not a polymer. Bambu Lab's PAHT-CF is "PA 12 and other long-chain PA, carbon fiber"; other brands sell PPA- or PA6-based filament under the same letters. If a drawing says PAHT-CF, ask whose datasheet it means before comparing figures. The figures on this page are Bambu Lab's. If a drawing asks for PA12 itself, see the PA12 alternatives guide.
Carbon fibre nylon is often sold as PA-CF; ours is PPA-CF, with PA6-CF and PAHT-CF ordered in. It is also sold under generic names that say nothing about which nylon is inside. When a drawing names a filament we do not list, send it and we say which of the three it is closest to.
How we print it
PPA-CF is among our most popular materials and usually prints in 2-5 working days after payment. PA6-CF and PAHT-CF are ordered in for the job; the quote gives the time. Ask for two materials in one request and the quote prices each.
- Largest carbon fibre nylon part in one piece: 340 x 320 x 340 mm. All three print in a heated chamber.
- Strength across the layers is a third of the figure along them for PPA-CF (57 against 168 MPa). A person checks the orientation against your load before the price; if the load must cross the layers, say so.
- Fine threads do not print well in a fibre-filled nylon. The hole is printed plain and the thread cut afterwards.
- Tolerance ±0.5%, minimum ±0.5 mm. Parts are posted to the Baltics, Finland, Sweden and Denmark.
- Reply in 3 hours on average on workdays. One part is a real order.
Where carbon fibre nylon stops
It is not metal. PPA-CF can take the place of a machined bracket or a jig plate where the load is known and runs along the layers; it does not replace metal in every part. Send the load and we say.
We print chopped-fibre filament. Parts with continuous carbon fibre laid into them are a different process with different figures, and we do not make them.
A printed part carries no formal approval. Bambu Lab's figures are specimen tests; your part depends on its geometry, its orientation and the settings. Tell us the load, the temperature and what the part touches, and a person checks the three against them.
Questions
Checked by the druckworks workshopUpdated
Is PPA-CF a nylon?
Yes. PPA is a semi-aromatic nylon, and Bambu Lab's datasheet lists PPA-CF as "Semi-aromatic Nylon, carbon fiber". It is the carbon fibre nylon we print most.
Which carbon fibre nylon for a wet part?
PAHT-CF: 0.88% saturated water absorption, and Bambu Lab says it keeps its properties when wet. PA6-CF takes up 2.35% and its own datasheet places it in dry environments. No datasheet gives a wet-strength figure, so we quote none.
Which is the strongest?
PPA-CF: 168 MPa tensile strength along the layers (ISO 527) and 9,860 MPa bending modulus (ISO 178). PAHT-CF is the toughest along the layers: 57.5 kJ/m² impact (ISO 179). Strong and tough are different questions; say which one your part asks.
Which takes the most heat?
PPA-CF, 196 °C heat deflection at 1.8 MPa (ISO 75), then PAHT-CF at 170 °C and PA6-CF at 164 °C. For more than that, PPS-CF at 235 °C, which is not a nylon.
Is PAHT-CF the same as PA12-CF?
At Bambu Lab, nearly: the composition is "PA 12 and other long-chain PA, carbon fiber". At other brands PAHT-CF can be PPA- or PA6-based. Our figures are Bambu Lab's.
Can carbon fibre nylon replace a metal part?
In a bracket or a jig with a known load along the layers, often. Across the layers PPA-CF keeps a third of its strength (57 MPa), so a part loaded that way needs a look first. Send the load and we say.
Do you print PA6-GF?
Yes, ordered in. Glass fibre instead of carbon; its impact across the layers is 4.1 kJ/m² (ISO 179), lower than any of the three here, and Bambu Lab lists brittleness when dry among its cons.
Do you post carbon fibre nylon parts to Lithuania?
Yes. We post to Latvia, Estonia, Lithuania, Finland, Sweden and Denmark; the quote names the carrier and the price.
Send the part, we pick the nylon
Send the file and say what the part carries, how warm it gets and whether it gets wet. A person picks between PPA-CF, PA6-CF and PAHT-CF and replies with a price in 3 hours on average on workdays.
